Skip to content
Launch Dealer SA

Technical guides

Crank Sensor Fault P0335: Test Before Replacing

Crank sensor symptoms and P0335 explained for African workshops: live RPM while cranking, Hall vs inductive tests, reluctor ring checks and relearns.

By the technical team at Launch Dealer SA · 20 November 2026 · 8 min read

Short answer: crank sensor symptoms usually show up as a crank-no-start, an engine that cuts out when hot and restarts when cool, or an intermittent stall with code P0335 (crankshaft position sensor circuit). Don't fit a new sensor on the code alone. First watch engine RPM in live data while cranking: if it reads zero or drops out while the engine is clearly turning, the ECU is not getting a usable crank signal. Then test the wiring, the reference voltage and the reluctor (trigger) ring before you condemn the sensor. A new crankshaft position sensor often fails to fix the fault because the real cause is a chafed wire, a bad ground, a shorted 5 V reference or a damaged tooth on the ring.

This guide is written for workshops in South Africa and across Africa. It follows the order we would use on any petrol or diesel engine with a scan tool: confirm the symptom, read the code properly, watch the live signal, test the circuit, then replace and relearn only what is proven faulty.

Crank sensor symptoms

The crankshaft position sensor tells the ECU how fast the engine is turning and where the crank is in its rotation. The ECU uses that signal for injection and ignition timing, and on most engines it will not fire injectors or coils without it. That is why crank sensor symptoms tend to be dramatic:

  • Cranks but won't start. The starter turns the engine normally, but there is no spark or injection because the ECU sees no RPM.
  • Cuts out when hot, restarts when cool. A classic failing sensor or cracked wire. Heat opens a break in the coil winding or the loom, and the signal returns once it cools.
  • Intermittent stalling or a stumble at speed, sometimes with the tacho needle dropping to zero for a moment.
  • Tacho needle doesn't move while cranking on vehicles where the cluster takes RPM from the engine ECU.
  • Misfire or rough running, because a noisy crank signal confuses the misfire monitor. Our P0300 misfire guide explains how the ECU uses crank speed to count misfires.
  • Hard starting with long cranking before the engine catches.

Many of these symptoms overlap with fuel pump, immobiliser and camshaft sensor faults. That is why the next steps matter more than the symptom list.

What P0335-P0339 mean

These are generic OBD2 codes, so the wording is similar on most makes. Manufacturers can add their own codes and sub-types, so always read the full description your scan tool gives.

CodeMeaningWhat it points to
P0335Crankshaft position sensor "A" circuitNo signal or an implausible signal: open circuit, failed sensor, missing reference voltage
P0336Circuit range/performanceA signal exists but is wrong: missing or damaged teeth, wrong air gap, electrical noise, slipping or damaged trigger ring
P0337Circuit lowSignal shorted to ground, or reference voltage pulled low
P0338Circuit highSignal shorted to voltage, or an open ground
P0339Circuit intermittentSignal drops in and out: loose connector, chafed wire, heat-related sensor failure

The real technical distinction is between P0335 and P0336. P0335 says the ECU is not seeing a usable signal at all, which points at the circuit or the sensor. P0336 says the signal is there but doesn't make sense, which often points at the mechanical side: the reluctor ring, the flywheel, the air gap or interference. A new sensor rarely fixes a P0336 caused by a damaged ring.

Also check for camshaft and correlation codes stored with it (such as P0340 and P0016). A cam code plus a crank code together can mean a shared reference voltage, a shared ground or a timing problem rather than two failed sensors. Our fault codes guide covers how to read freeze frame data and stored versus pending codes.

Live RPM while cranking

This is the quickest and most useful test, and it needs only a scan tool with live data.

  1. Connect the scan tool, open the engine module and select engine RPM in live data. If the vehicle offers a crank or cam sync status item, add it too.
  2. Crank the engine for a few seconds and watch RPM.
  3. A healthy crank signal shows a steady cranking speed, usually in the low hundreds of RPM depending on the engine and battery condition.
  4. Zero RPM while cranking means the ECU sees no crank signal. Go to the wiring tests.
  5. RPM that jumps, drops out or reads far too high points to a noisy or intermittent signal: a damaged ring, a loose sensor, a poor connector or interference from damaged shielding.
  6. For heat-related faults, run the engine up to temperature (or until it cuts out) and record live data. If your scan tool can record or graph live data, capture the moment of the stall.

Note that a scan tool shows the RPM the ECU has calculated, not the raw sensor waveform. It tells you whether the ECU is getting a usable signal, which is enough to decide where to look next. To see the actual waveform, missing teeth or a weak signal amplitude, you need an oscilloscope. Our live data guide explains which parameters to graph and how to compare readings.

Wiring and reluctor ring checks

Before you order a sensor, prove the circuit. First identify which type of sensor the engine uses, from the workshop information for that engine. It matters because they are tested differently.

Inductive (magnetic) sensors usually have two wires. They generate their own AC signal as the teeth pass, and the voltage rises with engine speed. You can check coil resistance with a multimeter against the manufacturer's specification, and check the AC voltage while cranking. A weak signal at cranking speed can stop the engine starting even though it runs at higher RPM.

Hall-effect sensors usually have three wires: a reference supply (commonly 5 V, sometimes 12 V), a ground and a signal. They produce a square-wave on/off signal and cannot be checked with a resistance test. Test them powered:

  • Reference voltage at the connector with the ignition on. Missing reference is a wiring or ECU supply problem, not a sensor fault.
  • Ground with a voltage-drop test, not just continuity. A corroded ground can pass a continuity test and still fail under load.
  • Signal switching while you turn the engine slowly by hand, or a frequency reading while cranking.

The shared 5 V reference trap. On many engines the crank sensor shares a 5 V reference with other sensors, such as the cam sensor or pressure sensors. If any one of them shorts internally, it pulls the reference down and the crank sensor loses power. Unplug the other sensors on that reference one at a time and watch whether the crank signal or reference voltage returns.

Wiring and connector. Check the loom near the exhaust, the starter and the engine mounts, where heat and movement cause chafing. Do a wiggle test with live data running. Look for oil inside the connector, which can come from a leaking seal and wick along the wire.

Reluctor ring and air gap. Remove the sensor and look at the tip and the ring:

  • Metal debris stuck to a magnetic sensor tip can distort the signal.
  • A chipped, bent or missing tooth on the reluctor ring or flywheel causes P0336-type faults. The larger "missing tooth" gap on many rings is normal; it is the reference point the ECU uses for TDC.
  • A loose or slipped trigger ring, or a damaged flywheel after clutch work, changes the timing reference.
  • Check the air gap where the design allows it. A sensor that isn't fully seated, or a spacer left out, can cause a weak signal.

Fitting and relearn

Once you have proven the sensor faulty:

  1. Fit a quality sensor of the correct type and part number. Cheap sensors with the wrong output are a common cause of repeat faults.
  2. Check the O-ring and seating so the air gap is correct.
  3. Clear the codes, then confirm cranking RPM in live data before road testing.
  4. Check whether the vehicle needs a relearn. Some makes require a crankshaft position variation (or crank tooth) relearn after the sensor, flywheel, crankshaft or ECU is replaced, so the misfire monitor can learn the small differences between teeth. Without it, some vehicles set misfire codes or keep the check engine light on. Whether a relearn is needed, and the exact procedure, depends on the make and model, so check the service procedure for that vehicle. Where LAUNCH supports it, it is listed under the vehicle's special or service functions. Check with us before you buy if this is a job you do often on a particular make.
  5. Drive the vehicle through a full warm-up and confirm the code does not return.

The same process applies whatever the badge, whether it is a Polo Vivo, a bakkie or a Japanese import. Only the sensor type, location and relearn procedure change, so look those up for the exact engine rather than guessing.

Tools

You need three things for crank sensor diagnosis: a scan tool with reliable live data, a multimeter, and ideally an oscilloscope for waveform work.

  • [LAUNCH X431 PROS Elite](/products/launch-x-431-pros-elite-professional-diagnostic-scanner), R 11 590 on our live product page today. Full-system diagnostics with live data, bi-directional tests, ECU coding and 32+ service functions. A strong first professional tablet for this kind of diagnosis on 16-pin OBD2 vehicles.
  • [LAUNCH X431 PRO3 APEX](/products/launch-x431-pro3-apex-obd2-scanner), R 21 490 on our live product page today. Adds live data streaming with graphing, 37+ service functions and a non-16-pin adapter set for older vehicles with non-standard diagnostic plugs.

Neither of these is an oscilloscope, so for raw waveform work you will still need a scope. Coverage of every function depends on the make, model, year and control module. Tell us the vehicles you work on and we will check before you buy. LAUNCH restricts software updates by sales territory, so buy a unit sold for your sales territory.

FAQ

Can a car start with a bad crank sensor?

Usually not, if the signal is completely lost, because most ECUs will not fire the injectors or coils without a crank signal. A failing sensor can still let the engine start and then cut out when hot, stall intermittently or cause hard starting. A few engines can run on a cam signal as a backup, but it is not something to rely on.

Does a new crank sensor need a relearn?

Some vehicles do. Certain makes need a crankshaft position variation relearn after the sensor, flywheel, crankshaft or ECU is replaced, otherwise misfire codes can return. Others need nothing. Check the service procedure for the exact vehicle, and check with us whether your LAUNCH tool supports that relearn for it.

Hall vs inductive sensors?

An inductive sensor usually has two wires and generates its own AC signal, which gets stronger with engine speed; you can test its resistance. A Hall-effect sensor usually has three wires (reference supply, ground and signal) and produces a square-wave signal; it must be tested powered, not with a resistance check.

See it before you buy

See the LAUNCH X431 PROS Elite, or browse the professional workshop range.

Can't get to Midrand? Book a WhatsApp video demo and we will show you live data on a running vehicle. Our showroom is at Shop AG008, Midrand Motor City.

Questions we get asked

Can a car start with a bad crank sensor?

Usually not, if the signal is completely lost, because most ECUs will not fire the injectors or coils without a crank signal. A failing sensor can still let the engine start and then cut out when hot, stall intermittently or cause hard starting.

Does a new crank sensor need a relearn?

Some vehicles do. Certain makes need a crankshaft position variation relearn after the sensor, flywheel, crankshaft or ECU is replaced, otherwise misfire codes can return. Check the service procedure for the exact vehicle, and check with us whether your LAUNCH tool supports that relearn for it.

Hall vs inductive sensors?

An inductive sensor usually has two wires and generates its own AC signal that gets stronger with engine speed; you can test its resistance. A Hall-effect sensor usually has three wires (reference supply, ground and signal) and produces a square-wave signal; it must be tested powered.

Talk to a technician

Not sure which one you need?

Tell us the vehicles you work on and the jobs you need to do, and we’ll point you to the right tool. Closed — opens tomorrow at 08:00.